Jump to content

List of DIN standards

From Wikipedia, the free encyclopedia

This is an incomplete list of DIN standards.

  • The "STATUS" column gives the latest known status of the standard.
    • If a standard has been withdrawn and no replacement specification is listed, either the specification was withdrawn without replacement or a replacement specification could not be identified.
  • DIN stands for "Deutsches Institut für Normung", meaning "German institute for standardization". DIN standards that begin with "DIN V" ("Vornorm", meaning "pre-standard") are the result of standardization work, but because of certain reservations on the content or because of the divergent compared to a standard installation procedure of DIN, they are not yet published standards.

DIN 1 to DIN 999

[edit]

DIN 1 to DIN 99

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 1 Cone Pins, untempered Withdrawn DIN EN 22339 ISO 2339
DIN 3 Standard measurements Withdrawn
DIN 5 Technical drawings – Axonometric projections, Isometric projection Withdrawn DIN ISO 5456-1, DIN ISO 5456-2,
DIN ISO 5456-3, DIN ISO 5456-4
ISO 5456-1, ISO 5456-2,
ISO 5456-3, ISO 5456-4
DIN 5-10 Technical drawings – projections, terms Withdrawn DIN ISO 10209-2 ISO 10209-2
DIN 6 Projection displays in Normal, views and special presentations Withdrawn DIN ISO 128, DIN EN ISO 128 ISO 128
DIN 7 Parallel Pins Withdrawn DIN EN ISO 2338 ISO 2338
DIN 11 Whitworth pipe threads 1/4"-6" Thread diameter, sizes, teaching information Withdrawn
DIN 13-1 ISO general purpose metric screw threads – Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mm Active
DIN 13-2 ISO general purpose metric screw threads – Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm Active
DIN 13-3 ISO general purpose metric screw threads – Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm Active
DIN 13-4 ISO general purpose metric screw threads – Part 4: Nominal sizes for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110 mm Active
DIN 13-5 ISO general purpose metric screw threads – Part 5: Nominal sizes for 1 mm and 1,25 mm fine pitch threads; nominal diameter from 7,5 mm to 200 mm Active
DIN 13-6 ISO general purpose metric screw threads – Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mm Active
DIN 13-7 ISO general purpose metric screw threads – Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mm Active
DIN 13-8 ISO general purpose metric screw threads – Part 8: Nominal sizes for 3 mm fine pitch threads; nominal diameter from 28 mm to 300 mm Active
DIN 13-9 ISO general purpose metric screw threads – Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mm Active
DIN 13-10 ISO general purpose metric screw threads – Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm Active
DIN 13-11 ISO general purpose metric screw threads – Part 11: Nominal sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to 1000 mm Active
DIN 13-12 ISO general purpose metric screw threads – Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitches Active
DIN 13-13 ISO general purpose metric screw threads – Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizes Active
DIN 13-19 ISO general purpose metric screw threads – Part 19: Nominal profiles Active
DIN 13-20 ISO general purpose metric screw threads – Part 20: Limits of sizes for coarse pitch threads with the preferred tolerance classes; nominal sizes from 1 mm to 68 mm Active
DIN 13-21 ISO general purpose metric screw threads – Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm Active
DIN 13-22 ISO general purpose metric screw threads – Part 22: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 25 mm to 52 mm Active
DIN 13-23 ISO general purpose metric screw threads – Part 23: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 53 mm to 110 mm Active
DIN 13-24 ISO general purpose metric screw threads – Part 24: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 112 mm to 180 mm Active
DIN 13-25 ISO general purpose metric screw threads – Part 25: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 182 mm to 250 mm Active
DIN 13-26 ISO general purpose metric screw threads – Part 26: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 252 mm to 1000 mm Active
DIN 13-28 ISO general purpose metric screw threads – Part 28: Coarse and Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root Cross-sections, Tensile Stress Cross-sections and Pitch Angles Active
DIN 13-50 ISO general purpose metric screw threads – Part 50: Combination of tolerance classes for formed internal screw threads Active
DIN 13-51 ISO general purpose metric screw threads – Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes Active
DIN 13-52 ISO general purpose metric screw threads – Part 52: Multi-start thread tolerances and deviation of profile Active
DIN 15-2 Technical drawings; lines; general application Withdrawn DIN ISO 128-24
DIN 16 Oblique Standard Typeface for Drawings Withdrawn
DIN 17 Upright Standard Typeface for Drawings Withdrawn
DIN 38 Plain bearings; bearing metal lining for thick-walled multilayer plain bearings Active
DIN 74 Countersinks for countersunk head screws (except screws with DIN EN 27721 head) Active
DIN 76-1 Thread run-outs and thread undercuts for ISO metric threads in accordance with DIN 13-1 Active
DIN 76-2 Thread run-outs and thread undercuts for pipe threads conforming to ISO 228 part 1 Active
DIN 76-3 Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and Knuckle Threads and other Threads of Coarse Pitch Active
DIN 78 Protrusions of bolt ends Active DIN EN ISO 4753 (governs thread ends for bolts assembled with hexagon slotted nuts) ISO 4753
DIN 84 Product grade A slotted cheese head screws Withdrawn DIN EN ISO 1207 ISO 1207
DIN 85 Product grade A slotted pan head screws Withdrawn DIN EN ISO 1580 ISO 1580
DIN 88 Product slotted oval head countersunk machine screws Withdrawn ISO 2010-1983[1]
DIN 93 Tab washers with long tab Withdrawn
DIN 94 Split pins Withdrawn DIN EN ISO 1234 ISO 1234
DIN 95 Slotted Raised Countersunk (Oval) Head Wood Screws Active
DIN 96 Slotted Round Head Wood Screws Active

DIN 100 to DIN 199

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 101 Rivets – Technical specifications Active
DIN 103-1 ISO Metric Trapezoidal Screw Thread; Profiles Active
DIN 103-2 ISO Metric Trapezoidal Screw Thread; General Plan Active
DIN 103-3 ISO Metric Trapezoidal Screw Thread; Allowances and Tolerances for Trapezoidal Screw Threads of General Purpose Active
DIN 103-4 ISO Metric Trapezoidal Screw Thread; Nominal Dimensions Active
DIN 103-5 ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal Diameter Active
DIN 103-6 ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 105 to 300 mm Nominal Diameter Active
DIN 103-7 ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 8 to 100 mm Nominal Diameter Active
DIN 103-8 ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 105 to 300 mm Nominal Diameter Active
DIN 103-9 ISO metric trapezoidal screw threads; gauging of external and internal threads; gauge dimensions and design features Active
DIN V 105-1 Clay masonry units – Part 1: Solid and hollow bricks with density classes of 1,2 Withdrawn DIN V 105-100, DIN EN 771-1 EN 771-1
DIN V 105-2 Clay masonry units – Part 2: Solid and hollow bricks with density classes equal 1.0 Withdrawn DIN V 105-100, DIN EN 771-1 EN 771-1
DIN 105-3 Clay masonry units – Part 3: Tile and high strength-high-strength clinker Withdrawn DIN V 105-100, DIN EN 771-1 EN 771-1
DIN 105-4 Clay masonry units – Part 4: Ceramic bricks Withdrawn DIN V 105-100, DIN EN 771-1,
DIN EN 772-7
EN 771-1, EN 772-7
DIN 105-5 Clay masonry units – Part 5: Lightweight long-hole brick and light long-hole brick panels Active
DIN V 105-6 Clay masonry units – Part 6: High precision units Active
DIN V 105-100 Clay masonry units – Part 100: Clay masonry units with specific properties Active
DIN 125 Washers; medium type, primarily for hexagon bolts Withdrawn DIN EN ISO 7089,
DIN EN ISO 7090
ISO 7089,
ISO 7090
DIN 125-1 Product grade A washers – with a hardness up to 250 HV designed for use with hexagon head bolts and nuts Withdrawn DIN EN ISO 7089,
DIN EN ISO 7090
ISO 7089,
ISO 7090
DIN 125-2 Product grade A washers – with a hardness up to 300 HV designed for use with hexagon head bolts and nuts Withdrawn DIN EN ISO 7089,
DIN EN ISO 7090
ISO 7089,
ISO 7090
DIN 126 Product grade C washers – designed for use with hexagon head bolts and nut Withdrawn DIN EN ISO 7091 ISO 7091
DIN 127 Spring lock washers with square ends or tang ends Withdrawn
DIN 128 Curved and wave spring lock washers Withdrawn
DIN 137 Spring washers, curved or wave Withdrawn
DIN 174 Bright Flat Steel; Dimensions, Permissible Variations, Weights Withdrawn DIN EN 10278
DIN 175 Polished round steel; Dimensions, Permissible deviations according to ISO tolerance zone h9 Withdrawn DIN EN 10278

DIN 200 to DIN 299

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 201 Technical drawings; Hatchings; Representation of cutting edges and materials Withdrawn DIN ISO 128-50 ISO 128-50
DIN 209 Machine Reamers with Screwed-on Blades Active
DIN 267-1 Fasteners – Part 1: Technical delivery conditions; General requirements Withdrawn ISO 8992
DIN 267-2 Fasteners – Part 2: Technical delivery conditions; Bolts, Screws, Nuts and Similar Threaded and Formed Parts; Types and Dimensional Accuracy Active DIN EN ISO 4759-1 ISO 4759-1
DIN 267-3 Fasteners – Part 3: Technical delivery conditions; Property classes for carbon steel and alloy steel bolts and screws; Conversion of property classes Withdrawn DIN EN ISO 898-1 ISO 898-1
DIN 267-4 Fasteners – Part 4: Technical delivery conditions; Property classes for nuts (previous classes) Withdrawn DIN EN ISO 898-2 ISO 898-2
DIN 267-5 Fasteners – Part 5: Technical delivery conditions; Acceptance inspection; modified version of ISO 3269, 1984 edition Withdrawn DIN EN ISO 3269 ISO 3269
DIN 267-6 Fasteners – Part 6: Technical delivery conditions; Designs and accuracy of measurement for product grade F Active
DIN 267-7 Fasteners – Part 9: Technical delivery conditions; Bolts made of unalloyed or low-alloy steels Withdrawn DIN EN ISO 898-1 ISO 898-1
DIN 267-9 Fasteners – Part 9: Technical delivery conditions; Components with Electroplated Coatings Withdrawn DIN EN ISO 4042 ISO 4042
DIN 267-10 Fasteners – Part 10: Technical delivery conditions; Hot dip galvanized parts Withdrawn DIN EN ISO 10684 ISO 10684
DIN 267-11 Fasteners – Part 11: Technical delivery conditions (with additions to ISO 3506); Corrosion-resistant stainless steel fasteners Withdrawn
DIN 267-12 Fasteners – Part 12: Technical delivery conditions; Self-tapping screws Withdrawn DIN EN ISO 2702 ISO 2702
DIN 267-13 Fasteners – Part 13: Technical delivery conditions; Components for Bolted Connections Made Mainly from Materials Exhibiting a High Impact Strength at Low Temperature or from Materials with a High Temperature Strength Active
DIN 267-15 Fasteners – Part 15: Technical delivery conditions; Prevailing torque type nuts Withdrawn DIN EN ISO 2320,
DIN EN ISO 3506-1,
DIN EN ISO 3506-2,
DIN EN ISO 3506-3
ISO 2320,
ISO 3506-1,
ISO 3506-2,
ISO 3506-3
DIN 267-18 Fasteners – Part 18: Technical delivery conditions; Components made of Non-ferrous Metals Withdrawn DIN EN 28839 ISO 8839
DIN 267-19 | Withdrawn DIN EN ISO 26157-1,
DIN EN ISO 26157-3
ISO 6157-1,
ISO 6157-3
DIN 267-20 Fasteners – Part 20: Technical delivery conditions; Surface discontinuities on nuts Withdrawn DIN EN ISO 6157-2,
DIN EN ISO 10484,
DIN EN ISO 10485
ISO 6157-2,
ISO 10484,
ISO 10485
DIN 267-21 Fasteners – Part 21: Technical delivery conditions; Widening test on nuts Withdrawn DIN EN ISO 6157-2,
DIN EN ISO 10484,
DIN EN ISO 10485
ISO 6157-2,
ISO 10484,
ISO 10485
DIN 267-23 Fasteners – Part 23: Technical delivery conditions; Property classes for nuts with fine thread (ISO classes) Withdrawn DIN EN ISO 898-6 ISO 898-6
DIN 267-24 Fasteners – Part 24: Technical delivery conditions; Property classes for nuts (Hardness classes) Active
DIN 267-25 Fasteners – Part 25: Technical delivery conditions; Torsion testing of M1 to M10 bolts and screws Withdrawn DIN EN 20898-7 EN 20898-7
DIN 267-26 Fasteners – Part 26: Technical delivery conditions; Conical spring washers for bolt/nut assemblies Active
DIN 267-27 Fasteners – Part 27: Technical specifications; Steel screws, bolts and studs with adhesive coating Active
DIN 267-28 Fasteners – Part 28: Technical specifications; Steel screws, bolts and studs with locking coating Active
DIN 267-29 Fasteners – Part 29: Technical specifications; Product grades for parts for bolted connections for use at temperatures ranging from −200 °C to +700 °C Withdrawn
DIN 267-30 Fasteners – Part 30: Technical specifications; Metric thread rolling screws of property class 10.9 Active
DIN 276-1 Building costs; Part 1: Building construction Active
DIN 276-2 Building costs; Part 2: Classification of cost Withdrawn
DIN 276-3 Building costs; Part 3: Ascertainment of cost Withdrawn

DIN 300 to DIN 399

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 315 Wing nuts with rounded wings Active
DIN 316 Wing screws with rounded wings Active
DIN 317 Drill drifts for taper shanks with drift tang Active
DIN 323-1 Preferred Numbers and Series of Preferred Numbers; Basic Values, Calculated Values, Rounded Values Withdrawn
DIN 323-2 Preferred Numbers and Series of Preferred Numbers; Introduction Active
DIN 332-1 60° centre holes; types R, A, B, and C Active
DIN 332-2 Center holes 60° with thread for shaft ends for rotating electrical machines Active
DIN 332-4 Centre holes for rail vehicles axles Active
DIN 332-7 Machine tools; 60° centre holes; dimensioning Active
DIN 332-8 Centre holes 90°, form S; dimensions, determination process Active
DIN 332-10 Center Holes; Indications on Technical Drawings Withdrawn DIN ISO 6411 ISO 6411
DIN 338 Parallel shank twist drills, jobber series Active
DIN 352 Sets of taps – Sets of 3 taps for metric coarse ISO-threads M1 to M68 Active
DIN 371 Machine taps with reinforced shank for coarse pitch metric ISO-threads M1 to M10 and fine pitch metric ISO-threads M1 × 0,2 to M10 × 1,25 Active
DIN 374 Machine screwing taps for fine pitch metric ISO-threads M3 × 0,2 to M52 × 4 Active

DIN 400 to DIN 499

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 404 Slotted capstan screws Active
DIN 406-10 Engineering drawing practice; dimensioning; concepts and general principles Active
DIN 406-11 Engineering drawing practice; dimensioning; principles of application Active
DIN 406-12 Engineering drawing practice; dimensioning; tolerancing of linear and angular dimensions (modified version of ISO 406:1987) Active
DIN 417 Slotted set screws with long dog point Withdrawn DIN EN 27435 ISO 7435
DIN 427 Slotted headless screws with chamfered end Withdrawn DIN EN ISO 2342 ISO 2342
DIN 428 Hexagon nuts, Grade C Withdrawn DIN EN ISO 4034 ISO 4034
DIN 433 Washers for use with cheese head screws Withdrawn DIN EN ISO 7092 ISO 7092
DIN 433-1 Product grade A washers – with a hardness up to 250 HV designed for use with cheese head screws Withdrawn DIN EN ISO 7092 ISO 7092
DIN 433-2 Product grade A washers – with a hardness up to 300 HV designed for use with cheese head screws Withdrawn DIN EN ISO 7092 ISO 7092
DIN 438 Slotted set screws with cup point Withdrawn DIN EN 27436 ISO 7436
DIN 439 Hexagon thin nuts Withdrawn DIN EN ISO 4035, DIN EN ISO 4036, DIN EN ISO 8675 ISO 4035, ISO 4036,
ISO 8675
DIN 439-1 Unchamfered hexagon thin nuts – Product grade B Withdrawn DIN EN ISO 4036 ISO 4036
DIN 439-2 Chamfered hexagon thin nuts – Product grades A and B Withdrawn DIN EN ISO 4035, DIN EN ISO 8675 ISO 4035, ISO 8675
DIN 440 Washers for use in timber constructions Withdrawn DIN EN ISO 7094 ISO 7094
DIN 444 Eyebolts Active
DIN 461 Graphical Representation in Systems of Coordinates Active
DIN 462 Machine Tools; Internal Tab Washers for Slotted Round Nuts for Hook Spanner according to DIN 1804 Active
DIN 464 Knurled thumb screws, high type Active
DIN 466 Knurled nuts, high type Active
DIN 467 Knurled nuts, low type Active
DIN 471 Circlips (retaining rings) for shafts; Normal type and heavy type Active
DIN 472 Circlips (retaining rings) for internal grooves; Normal type and heavy type Active
DIN 476 Paper sizes Withdrawn DIN EN ISO 216 ISO 216
DIN 476-2 Trimmed Sizes of Paper – C Series Active
DIN 477-1 Gas cylinder valves for cylinder test pressures up to 300 bar – Part 1: Valve inlet and outlet connections Active
DIN 479 Square head bolts with short dog point Active

DIN 500 to DIN 599

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 522 Metal washers; technical delivery conditions Withdrawn DIN EN ISO 4759-3 ISO 4759-3
DIN 548 Round nuts with set pin holes in side Active
DIN 551 Slotted set screws with flat point Withdrawn DIN EN 24766 ISO 4766
DIN 553 Slotted set screws with cone point Withdrawn DIN EN 27434 ISO 7434
DIN 555 M5 to M100x6 hexagon nuts – Product grade C Withdrawn DIN EN ISO 4034 ISO 4034
DIN 558 Hexagon head screws Withdrawn DIN EN ISO 4018 ISO 4018
DIN 580 Collar eyebolts for lifting purposes Active

DIN 600 to DIN 699

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 601 M5 to M52 hexagon head bolts; product grade C Withdrawn DIN EN ISO 4016 ISO 4016
DIN 603 Mushroom head square neck bolts Active
DIN 609 Hexagon fits bolts with long thread Active
DIN 625-1 Rolling bearings; single row radial contact ball bearings Active
DIN 625-3 Rolling bearings; double row radial contact ball bearings Active
DIN 625-4 Rolling bearings; radial contact groove ball bearings with flanged outer ring Active
DIN 653 Knurled thumb screws, low type Active
DIN 678-1 Envelopes – Part 1: Sizes Active
DIN 678-2 Envelopes – Part 2: Envelopes for Processing in Enveloping Machines, Size C6 to C4 Active

DIN 700 to DIN 799

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 763 Tested, non-calibrated, long-link round steel chains Active
DIN 764-1 Calibrated and tested round steel link chains for continuous conveyors; grade 2, pitch 3,5d Active
DIN 764-2 Calibrated and tested round steel link chains for continuous conveyors; grade 3, pitch 3,5d Active
DIN 766 Calibrated and tested grade 3 round steel link chains Active
DIN 799-1 Foundation Blocks Active

DIN 800 to DIN 899

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 820-1 Standards Work – Part 1: Principles Active
DIN 820-2 Standardization – Part 2: Presentation of standards; examples for presentation of figures, tables and part lists Active
DIN 820-3 Standardization – Pdfart 3: Concepts Active
DIN 820-4 Standardization – Part 4: Working procedure Active
DIN 820-11 Standardization – Part 11: Presentation of Standards concerning safety regulations which are VDE-Specifications or VDE-Guidelines Active
DIN 820-12 Standardization – Part 12: Presentation of standards concerning safety regulations Active
DIN 820-13 Standardization – Part 13: Adoption of European documents of CEN, CENELEC and of ETSI; Concepts and presentation Active
DIN 820-15 Standardization – Part 15: Implementation of ISO and IEC international documents; Concepts and presentation Active
DIN 820-120 Standardization – Part 120: Guidelines for the inclusion of safety aspects in standards (ISO/IEC Guide 51:1999) Active
DIN 824 Technical drawings; Folding to filing size Active
DIN 899 Hand Operated Wrenches and Sockets; Technical Specifications Withdrawn DIN ISO 1711-1 ISO 1711-1

DIN 900 to DIN 999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 906 internal drive pipe plugs for the sealing of holes with cylindrical internal threads Active
DIN 908 Hexagon socket screw plugs with parallel screw thread Active
DIN 910 Hexagon-duty hexagon head screw plugs Active
DIN 911 Hexagon Socket Screw Keys Withdrawn DIN ISO 2936 ISO 2936
DIN 912 Hexagon socket head cap screws (modified version of ISO 4762) Withdrawn DIN EN ISO 4762,
DIN EN ISO 21269
ISO 4762,
ISO 21269
DIN 913 Hexagon socket set screws with flat point (ISO 4026 modified) Withdrawn DIN EN ISO 4026 ISO 4026
DIN 914 Hexagon socket set screws with cone point (ISO 4027 modified) Withdrawn DIN EN ISO 4027 ISO 4027
DIN 915 Hexagon socket set screws with dog point (ISO 4028 modified) Withdrawn DIN EN ISO 4028 ISO 4028
DIN 916 Hexagon socket set screws with cup point (ISO 4029 modified) Withdrawn DIN EN ISO 4029 ISO 4029
DIN 918 Fasteners; Terminology; Spelling of terms; Abbreviations Active
DIN 918-3 Overview of European Standards for fasteners Active
DIN 919-1 Technical Drawings; Wood Processing; Principles Active
DIN 921 Slotted pan head screws with large head Active
DIN 923 Slotted pan head screws with shoulder Active
DIN 929 Hexagon weld nuts Active
DIN 930 Fine thread pitch partially threaded screws Withdrawn DIN 931-1, DIN 931-2
DIN 931-1 M1,6 to M39 Hexagon Cap Screws Partially Threaded – Product grades A and B Withdrawn DIN EN ISO 4014 ISO 4014
DIN 931-2 M42 to M160x6 Hexagon Cap Screws Partially Threaded – Product grade B Withdrawn DIN EN ISO 4014 ISO 4014
DIN 933 M1,6 to M52 Hexagon Cap Screws Fully Threaded – Product grades 8.8 Withdrawn DIN EN ISO 4017 ISO 4017
DIN 934 Hexagon nuts with metric coarse and fine pitch thread – Product classes A and B Withdrawn DIN EN ISO 4032,
DIN EN ISO 8673
ISO 4032,
ISO 8673
DIN 935-1 Hexagon slotted nuts and castle nuts with metric coarse and fine pitch thread – Product grades A and B Active
DIN 935-2 M42 to M160x6 hexagon head nuts; product grade B Active
DIN 935-3 Hexagon slotted nuts with metric coarse pitch thread – Product grade C Active
DIN 936 M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product grades A and B Withdrawn
DIN 937 Hexagon thin castle nuts Withdrawn
DIN 938 Studs with a length of engagement equal to about 1 d Active
DIN 939 Studs with a length of engagement equal to about 1,25 d Active
DIN 946 Determination of coefficient of friction of bolt/nut assemblies under specified conditions Withdrawn DIN EN ISO 16047 ISO 16047
DIN 960 M8x1 to M100x4 hexagon head bolts with fine pitch thread – Product grades A and B Withdrawn DIN EN ISO 8765,
DIN EN ISO 8676
ISO 8765,
ISO 8676
DIN 961 M8x1 to M52x3 hexagon head bolts with fine pitch thread – Product grades A and B Withdrawn DIN EN ISO 8676 ISO 8676
DIN 962 Designation system for fasteners Active
DIN 963 Slotted countersunk head screws (with countersunk heads as specified in ISO 2009-1972) Withdrawn DIN EN ISO 2009 ISO 2009
DIN 964 Slotted raised countersunk oval head screws Withdrawn DIN EN ISO 2010 ISO 2010
DIN 965 Cross recessed countersunk flat head screws Withdrawn DIN EN ISO 7046-1,
DIN EN ISO 7046-2
ISO 7046-1,
ISO 7046-2
DIN 966 Cross recessed raised countersunk head screws Withdrawn DIN EN ISO 7047 ISO 7047
DIN 970 Hexagon nuts; Style 1; Metric coarse thread, Product grades A and B; ISO 4032 modified Withdrawn DIN EN ISO 4032 ISO 4032
DIN 971-1 Style 1 hexagon nuts with metric fine pitch thread; property classes 6 and 8 Withdrawn DIN EN ISO 8673 ISO 8673
DIN 971-2 Style 2 hexagon nuts with metric fine pitch thread; property classes 10 and 12 Withdrawn DIN EN ISO 8674 ISO 8674
DIN 972 M5 to M39 hexagon nuts; style 1; product grade C (modified version of ISO 4034) Withdrawn DIN EN ISO 4034 ISO 4034
DIN 975 Threaded rods Withdrawn DIN 976-1, DIN 976-2
DIN 976-1 Metric thread stud bolts Active
DIN 976-2 Metric interference-fit thread stud bolts Active
DIN 977 Hexagon weld nuts with flange Withdrawn DIN EN ISO 21670 ISO 21670
DIN 979 Hexagon thin slotted nuts and castle nuts with metric coarse and fine pitch thread – Product grades A and B Active
DIN 980 All-metal prevailing torque type hexagon nuts Withdrawn DIN EN ISO 7042,
DIN EN ISO 10513
ISO 7042,
ISO 10513
DIN 981 Locknuts for use with rolling bearings Active
DIN 982 Prevailing torque type hexagon nuts with nonmetallic insert Withdrawn DIN EN ISO 7040,
DIN EN ISO 10512
ISO 7040,
ISO 10512
DIN 983 Retaining rings with lugs for use on shafts (external circlips) Active
DIN 985 Prevailing torque type hexagon thin nuts with nonmetallic insert Withdrawn DIN EN ISO 10511 ISO 10511
DIN 986 Prevailing torque type hexagon domed cap nuts with non-metallic insert Active
DIN 988 Shim rings and supporting rings Active

DIN 1000 to DIN 9999

[edit]

DIN 1000 to DIN 1999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 1025-1 Hot rolled I-sections – Part 1: Narrow flange I-sections, I-serie – Dimensions, masses, sectional properties Active
DIN 1025-2 Hot rolled I-beams – Part 2: Wide flange I-beams, IPB-serie; dimensions, masses, sectional properties Active
DIN 1025-3 Hot rolled I-beams; wide flange I-beams, light pattern, IPBl-serie; dimensions, masses, sectional properties Active
DIN 1025-4 Hot rolled I-beams; wide flange I-beams heavy pattern, IPBv-serie; dimensions, masses, sectional properties Active
DIN 1025-5 Hot rolled I-beams; medium flange I-beams, IPE-serie; dimensions, masses, sectional properties Active
DIN 1301-1 Units – Part 1: Names and Symbols Active
DIN 1301-2 Units – Part 2: Submultiples and Multiples for General Use Active
DIN 1301-3 Units – Part 3: Conversions of Units No Longer To Be Used Active
DIN 1302 General Mathematical Symbols and Concepts Active
DIN 1303 Vectors, matrices, tensors; symbols and concepts Active
DIN 1304-1 Letter symbols for physical quantities – Part 1: Symbols for general use Active
DIN 1304-2 Letter symbols for physical quantities – Part 2: Symbols for use in meteorology and geophysics Active
DIN 1304-3 Letter symbols for physical quantities – Part 3: Symbols for use in electric power engineering Active
DIN 1304-5 Letter symbols for physical quantities – Part 5: Symbols for use in fluid mechanics Active
DIN 1304-8 Letter symbols for physical quantities – Part 9: Symbols for use in the field of static converters using semiconductor devices Active
DIN 1304-9 Letter symbols for physical quantities – Part 9: Symbols for equivalent circuits of piezoelectric crystals Active
DIN 1311-1 (Mechanical) vibrations, oscillations and vibration systems – Part 1: Basic concepts, survey Active
DIN 1311-2 (Mechanical) vibrations, oscillations and vibration systems – Part 2: Linear vibration systems with single degree of freedom Active
DIN 1311-3 (Mechanical) vibrations, oscillations and vibration systems – Part 3: Linear time-invariant vibration systems with a finite number of degrees of freedom Active
DIN 1311-4 Vibration; Vibrating Continua, Waves Active
DIN 1313 Physical Quantities and Equation; Concepts, Methods of Writing Active
DIN 1315 Angle; Concepts, Units Active
DIN 1318 Loudness Level Active
DIN 1319-1 Fundamentals of Metrology – Part 1: Basic Terminology Active
DIN 1319-2 Basic Concepts in Metrology – Part 2: Terminology Related To Measuring Equipment Active
DIN 1319-3 Basic Concepts in Metrology – Part 3: Terminology Relating To the Uncertainty of Measurement and the Assessment of Measuring Instruments and Measuring Equipment Active
DIN 1319-4 Basic Concepts in Metrology – Part 4: Treatment of Uncertainties in the Evaluation of Measurements Active
DIN 1320 Acoustics; Terminology Active
DIN 1324-1 Electromagnetic Field – Part 1. State Quantities Active
DIN 1324-2 Electromagnetic Field – Part 2. Material Quantities Active
DIN 1324-3 Electromagnetic Field – Part 3. Electromagnetic Waves Active
DIN 1325-1 Vocabulary for value management, value analysis and functional analysis – Part 1: Value analysis and functional analysis Active
DIN 1325-2 Value Management, Value Analysis, Functional Analysis Vocabulary – Part 2: Value Management Active
DIN 1332 Acoustics; Symbols Withdrawn DIN EN ISO 80000-8 ISO 80000-8
DIN 1333 Presentation of Numerical Data Active
DIN 1338 Writing and Typesetting of Formulae Active
DIN 1355-1 Time; Calendar, Numbering of Weeks, Date of Day, (Clock) Time Withdrawn
DIN 1421 Arrangement and Numbering in Texts; Clauses, Paragraphs, Enumerations Active
DIN 1422-1 Publications in Sciences, Technology, Economy and Administration; Presentation of Manuscripts and Typoscripts Active
DIN 1422-2 Publications in Sciences, Technology, Economy and Administration; Presentation of Clean Copies for Reprographic Use Active
DIN 1422-3 Publications in Sciences, Technology, Economy and Administration; Typographical Presentation Active
DIN 1422-4 Publications in Sciences, Technology, Economy and Administration; Presentation of Scientific and Technical Reports Active
DIN 1440 Medium type washers for pins Withdrawn DIN EN 28738 ISO 8738
DIN 1443 Clevis pins without head Withdrawn DIN EN 22340 ISO 2340
DIN 1444 Clevis pins with head Withdrawn DIN EN 22341 ISO 2341
DIN 1450 Legibility of Typefaces – General Active
DIN 1451-1 Lettering – Linear-Antiqua without serifes – General Active
DIN 1451-2 Typefaces – lineal Linear-Antiqua; lettering for transportation Active
DIN 1451-3 Lettering – Linear-Antiqua without serifes; lettering for printing Active
DIN 1451-4 Typefaces – lineal Linear-Antiqua; stenciled lettering for engraving and other processes Active
DIN 1463-1 Guidelines for the Establishment and Development of Thesauri; Monolingual Thesauri Active
DIN 1463-2 Guidelines for the Establishment and Development of Thesauri; Multilingual Thesauri Active
DIN 1470 Grooved Pins, Full Length Parallel-grooved with Pilot Withdrawn DIN EN 8739 ISO 8739
DIN 1471 Grooved Pins, Full Length Taper-grooved Withdrawn DIN EN 8744 ISO 8744
DIN 1472 Grooved Pins, Half Length Taper-grooved Withdrawn DIN EN 8745 ISO 8745
DIN 1473 Grooved Pins, Full Length Parallel-grooved with Chamfer Withdrawn DIN EN ISO 8740 ISO 8740
DIN 1474 Grooved Pins, Half Length Reverse-grooved Withdrawn DIN EN 8741 ISO 8741
DIN 1475 Grooved Pins, Third Length Centre-grooved Withdrawn DIN EN 8742 ISO 8742
DIN 1476 Round Head Grooved Pins Withdrawn DIN EN 8746 ISO 8746
DIN 1477 Countersunk Head Grooved Pins Withdrawn DIN EN 8747 ISO 8747
DIN 1481 Spring-Type Straight Pins (Roll Pins) – Heavy Type Withdrawn DIN EN ISO 8752 ISO 8752
DIN 1505-1 Bibliographic references to documents – Part 1: Full References to Printed and Published Documents Active
DIN 1505-2 Bibliographic references to documents – Part 2: Rules for Citing Active
DIN 1505-3 Bibliographic references to documents – Part 3: Indexes of cited documents (bibliographies) Active
DIN 1511 Pattern Equipment for Foundries; Production and Quality Withdrawn DIN EN 12890 EN 12890
DIN 1530-1 Tools for moulding – Part 1: Ejector pins with cylindrical head Active
DIN 1530-2 Tools for moulding – Part 2: Shouldered ejector pins Active
DIN 1530-3 Tools for moulding – Part 3: Ejector pins with conical head Active
DIN 1587 Hexagon domed cap nuts Active
DIN 1707 Soft Solders; Composition, Technical Delivery Condition Active DIN EN ISO 9453 ISO 9453
DIN 1712 Part 1 Aluminium and aluminium alloys – Unalloyed aluminium ingots for remelting – Specifications Withdrawn DIN EN 576 EN 576
DIN 1712 Part 3 Aluminium; Half-Finished Products Withdrawn DIN EN 573-3 EN 573-3
DIN 1783 Strips, Plates and Sheets of Aluminium and Wrought Withdrawn DIN EN 485-4 EN 485-4
DIN 1786 Seamless Drawn Copper Tubes for Piping Systems Withdrawn DIN EN 1057 EN 1057
DIN 1798 Round Rod of Aluminium (Highest Grade Aluminium) Withdrawn DIN EN 754-3 EN 754-3
DIN 1804 Slotted Round Nut for Hook Spanner; ISO Metric Fine Thread Active
DIN 1810 Hook wrenches Active
DIN 1816 Round Nut with Set Pin Holes Inside; ISO Metric Fine Thread Active
DIN 1897 Spiral drill bits, short length Active
DIN 1912-1 Graphical Representation of Welded, Soldered and Brazed Joints Withdrawn DIN EN ISO 17659 ISO 17659
DIN 1912-2 Graphical Representation of Welded, Soldered and Brazed Joints Withdrawn DIN EN ISO 6947 ISO 6947
DIN 1912-4 Graphical Representation of Welded, Soldered and Brazed Joints; Concepts and Terms for Soldered and Brazed Joints and Seams Active
DIN 1912-5 Symbolic Representation on Drawings of Welded, Soldered and Brazed Joints Withdrawn DIN EN 22553 ISO 2553
DIN 1960 Construction contract procedures (VOB) – Part A: General provisions relating to the award of construction contracts Active
DIN 1961 Construction contract procedures (VOB) – Part B: General conditions of contract relating to the execution of construction work Active

DIN 2000 to DIN 2999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 2112 Alphanumeric office machines – Alphanumeric keyboards, keyboard arrangement for manually operated typewriters Withdrawn DIN 2137-1, DIN 2137-2
DIN 2127 Alphanumeric office machines; alphanumeric keyboards, keyboard arrangement for electro-mechanical operated typewriters Withdrawn DIN 2137-1, DIN 2137-2
DIN 2137-1 Keyboards for data and text input – Part 1: German keyboard layout Active
DIN 2137-2 Keyboards for data and text input – Part 2: Additional requirements Active
DIN 2181 Sets of 2 taps for metric fine ISO-threads M1 × 0,2 to M52 × 4 Active
DIN 2342-1 Vocabulary of terminology; basic concepts Active
DIN 2391-1 Seamless precision steel tubes – Part 1: Dimensions Canceled DIN EN 10305-1 EN 10305-1
DIN 2391-2 Seamless precision steel tubes – Part 2: Technical delivery conditions Canceled DIN EN 10305-1 EN 10305-1
DIN 2448 Seamless Steel Pipes and Tubes – Dimensions, Conventional Masses per Unit Length Canceled DIN EN 10220 EN 10220
DIN 2527 Blank flanges – Nominal pressure 6 to 100 Withdrawn DIN EN 1092-1 EN 1092-1
DIN 2860 Capillary Fittings; Bends 180° of Copper Withdrawn
DIN 2982 Steel threaded pipe fittings Withdrawn DIN EN 10241 EN 10241
DIN 2999-1 Pipe threads for tubes and fittings; parallel internal thread and taper external thread; tread dimensions Withdrawn DIN EN 10226-1 EN 10226-1
DIN 2999-2 Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Internal Thread and Conical External Thread, Gauging System and Use of Gauges Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-3 Whitworth Pipe Threads for Tubes and Fittings; Gauge Dimensions Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-4 Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal thread Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-5 Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw Limit Ring Gauges for Gauging Conical External Threads, Sizes Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-6 Whitworth Pipe Threads for Tubes and Fittings; Conical Screw Check Plugs, Sizes Withdrawn DIN EN 10226-3 EN 10226-3

DIN 3000 to DIN 3999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 3000 ,
DIN 3017-1 Hose clamps with worm gear drive; shape A ,
DIN 3017-2 Hose clamps – Part 2: Clamps with fastening lugs ,
DIN 3017-3 Hose clamps – Part 3: Bolt clamps ,
DIN 3017-4 Hose clamps – Part 4: Technical delivery conditions ,
DIN 3017-5 Hose clamps – Part 5: Wide strip hose clamps with fastening lugs; Types D and E ,
DIN 3113 Combination Wrench ,
DIN 3770 Sealing rings ("O-rings") with special accuracy, made of elastomeric materials Withdrawn
DIN 3771-3 Fluid systems; O-rings; materials, field of application Active

DIN 4000 to DIN 4999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 4048-1 Water engineering, terms – Part 1: Dam plants Active
DIN 4048-2 Water engineering, terms – Part 2: Waterpower plants Active
DIN 4054 Correction of waterways, terms Active
DIN 4094-1 Subsoil, Field investigations – Part 1: Cone penetration tests Active
DIN 4102-1 Fire behaviour of building materials and elements – Part 1: Classification of building materials – Requirements and testing Active
DIN 4102-2 Fire Behaviour of Building Materials and Building Components – Part 2: Building Components; Definitions, Requirements and Tests Active
DIN 4102-3 Fire Behaviour of Building Materials and Building Components – Part 3: Fire Walls and Non-load-bearing External Walls; Definitions, Requirements and Tests Active
DIN 4102-4 Fire behaviour of building materials and elements – Part 4: Overview and design of classified building materials, elements and components Active
DIN 4102-5 Fire Behaviour of Building Materials and Building Components – Part 5: Fire Barriers, Barriers in Lift Wells and Glazings Resistant against Fire; Definitions, Requirements and Tests Active
DIN 4102-6 Fire Behaviour of Building Materials and Building Components – Part 6: Ventilation Ducts; Definitions, Requirements and Tests Active
DIN 4102-7 Fire behaviour of building materials and elements – Part 7: Roofing – Concepts, requirements and testing Active
DIN 4102-8 Fire behaviour of building materials and components – Part 8: Small-scale test furnace Active
DIN 4102-9 Fire behaviour of building materials and elements – Part 9: seals for cable penetrations; concepts, requirements and testing Active
DIN 4102-11 Fire behaviour of building materials and building components – Part 10: pipe encasements, pipe bushings, service shafts and ducts, and barriers across inspection openings; terminology, requirements and testing Active
DIN 4102-12 Fire behaviour of building materials and elements – Part 12: Fire resistance of electric cable systems required to maintain circuit integrity – Requirements and testing Active
DIN 4102-13 Fire behaviour of building materials and elements – Part 13: Fire resistant glazing; concepts, requirements and testing Active
DIN 4102-14 Fire behaviour of building materials and elements – Part 14: Determination of the burning behaviour of floor covering systems using a radiant heat source Active
DIN 4102-15 Fire behaviour of building materials and elements – Part 15: "Brandschacht" Active
DIN 4102-16 Fire behaviour of building materials and elements – Part 16: "Brandschacht" tests Active
DIN 4102-17 Fire behaviour of building materials and elements – Part 17: determination of melting point of mineral fibre insulating materials; concepts, requirements and testing Active
DIN 4102-18 Fire behaviour of building materials and components – Part 18: fire barriers, verification of automatic closure (continuous performance test) Active
DIN 4102-22 Fire behaviour of building materials and building components – Part 22: Application standard for DIN 4102-4 based on the design of partial safety factors Active
DIN 4108-1 Thermal protection and energy economy in buildings – Part 1: Quantities and units Active
DIN 4108-2 Thermal protection and energy economy in buildings – Part 2: Minimum requirements to thermal insulation Active
DIN 4108-3 Thermal protection and energy economy in buildings – Part 3: Protection against moisture subject to climate conditions; Requirements and directions for design and construction Active
DIN 4108-7 Thermal insulation and energy economy of buildings – Part 7: Airtightness of building, requirements, recommendations and examples for planning and performance Active
DIN 4108-10 Thermal insulation and energy economy in buildings – Part 10: Application-related requirements for thermal insulation materials – Factory made products Active
DIN 4150-1 Structural vibration – Part 1: Prediction of vibration parameters Active
DIN 4150-2 Structural vibration – Part 2: Human exposure to vibration in buildings Active
DIN 4150-3 Structural vibration – Part 3: Effects of vibration on structures Active
DIN 4420-1 Service and working scaffolds – Part 1: Service scaffolds – Performance requirements, general design, structural design Active
DIN 4512 Photographic sensitometry, determination of optical density: "Photographische Sensitometrie, Bestimmung der optischen Dichte" (1934-01, 1957–11, 1961–10) Withdrawn DIN 4512-1:1971-04, DIN 4512-3:1973-01, DIN 4512-4:1977-06, DIN 4512-5:1977-10, DIN 4512-6:1980-07
DIN 4512-1 Photographic sensitometry, determination of the speed of black and white negative materials for pictorial photography (1971-04, 1993–05) Withdrawn (2000–09) DIN ISO 6:1996-02 ISO 6
DIN 4512-3 Photographic sensitometry, determination of diffuse transmission density (1973-01) Withdrawn DIN 4512-7:1993-01, DIN 4512-8:1993-01, DIN 4512-9:1993-01
DIN 4512-4 Photographic sensitometry; determination of the speed of colour reversal films (1977-06, 1985–08) Withdrawn (2002–06) DIN ISO 2240:1998-06 ISO 2240
DIN 4512-5 Photographic sensitometry; determination of the speed of colour negative films (1977-10, 1990–11) Withdrawn (2002–06) DIN ISO 5800:1998-06 ISO 5800
DIN 4512-6 Photographic sensitometry; sensitometric illuminants and light sources (1980-07) Withdrawn
DIN 4512-7 Photographic sensitometry, determination of optical density; concepts, symbols and notations (1993-01) Active
DIN 4512-8 Photographic sensitometry, determination of optical density; geometric conditions for transmission density (1993-01) Active
DIN 4512-9 Photographic sensitometry, determination of optical density; spectral conditions (1993-01) Active
DIN 4512-10 Photographic sensitometry, determination of optical density; geometric conditions for reflection density (1993-01) Active
DIN V 4701-10 Energy efficiency of heating and ventilation systems in buildings – Part 10: Heating, domestic hot water supply, ventilation Active
DIN V 4701-12 Energetic evaluation of heating and ventilation systems in existing buildings – Part 12: Heat generation and domestic hot water generation Active
DIN 4710 Statistics on German meteorological data for calculating the energy requirements for heating and air conditioning equipment Active

DIN 5000 to DIN 5999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 5008 Rules for text presentation Active
DIN 5031-1 Physics of radiation in the field of optics and illuminating engineering – Part 1: Quantities, symbols and units of radiation physics Active
DIN 5031-2 Physics of radiation in the field of optics and illuminating engineering – Part 2: Evaluation of radiation by different detectors Active
DIN 5031-3 Physics of radiation in the field of optics and illuminating engineering – Part 3: Quantities, symbols and units of illuminating engineering Active
DIN 5031-4 Physics of radiation in the field of optics and illuminating engineering – Part 4: Efficiencies Active
DIN 5031-5 Physics of radiation in the field of optics and illuminating engineering – Part 5: Definitions for temperatures Active
DIN 5031-6 Physics of radiation in the field of optics and illuminating engineering – Part 6: Pupil intensity as a measure of retinal illumination Active
DIN 5031-7 Physics of radiation in the field of optics and illuminating engineering – Part 7: Terms for wavebands Active
DIN 5031-8 Physics of radiation in the field of optics and illuminating engineering – Part 8: Definitions and constants of radiation physics Active
DIN 5031-9 Physics of radiation in the field of optics and illuminating engineering – Part 9: Definitions in the field of luminescence Active
DIN 5031-10 Physics of radiation in the field of optics and illuminating engineering – Part 10: Photobiologically effective radiation, quantities, symbols and actions Active
DIN 5035-3 Artificial lighting – Part 3: Lighting of health care premises Active
DIN 5035-6 Artificial lighting – Part 6: Measurement and evaluation Active
DIN 5035-7 Artificial lighting – Part 7: Lighting of interiors with visual displays work stations Active
DIN 5035-8 Artificial lighting – Part 8: Workplace luminaries – Requirements, recommendations and proofing Active
DIN 5117 Clamp strength for woodworking Active
DIN 5145 Plane irons for wood smooth and for planes Active
DIN 5146 Curved irons for jack planes Active
DIN 5406 Lockwashers and locking plates for use with rolling bearings Active
DIN 5466-1 Splined joints, calculation of load capacity – Part 1: general basis Active
DIN 5473 Logic and set theory; symbols and concepts Active
DIN 5474 Signs in mathematical logic Withdrawn DIN 5473
DIN 5475-1 Complex quantities; nomenclature Withdrawn DIN 5483-3
DIN 5480-1 Involute splines based on reference diameters – Part 1: Generalities Active
DIN 5480-2 Involute splines based on reference diameters – Part 2: Nominal and inspection dimensions Active
DIN 5480-15 Involute splines based on reference diameters – Part 15: Inspection Active
DIN 5483-1 Time-dependent quantities – Part 1: Terms for the time-dependency Active
DIN 5483-2 Time-dependent quantities – Part 2: Letter symbols Active
DIN 5483-3 Time-dependent quantities – Part 3: Complex representation of sinusoidal time-dependent quantities Active
DIN 5486 Notation of matrices Withdrawn DIN 1303
DIN 5487 Fourier-, Laplace- and Z-transformation; symbols and concepts Active
DIN 5489 Directions and signs in electrical engineering; rules for electric and magnetic circuits, equivalent circuit diagrams Withdrawn DIN EN 60375 EN 60375
DIN 5493-2 Logarithmic quantities and units – Part 2: Logarithmic ratios, levels in nepers and decibels Active
DIN 5510-2 Fire test to railway components Active
DIN 5590 Compressed air equipment for rail vehicles – Pressure vessels made of steel – Dimensions, designation Active

DIN 6000 to DIN 6999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 6303 Knurled nuts Active
DIN 6304 Tommy screws with fixed clamping bolt Active
DIN 6305 Tommy nuts with fixed clamping bolt Active
DIN 6306 Tommy screws with movable clamping bolt Active
DIN 6307 Tommy nuts with movable clamping bolt Active
DIN 6310 Spring-loaded catch for jigs Active
DIN 6311 Thrust pads Active
DIN 6314 Clamp, straight Active
DIN 6315 Clamp, forked Active
DIN 6316 Goose neck clamp Active
DIN 6318 Stepped packing blocks as support for clamps Active
DIN 6319 Spherical washers and conical seats Active
DIN 6320 Feet with threaded shank for jigs and fixtures Active
DIN 6321 Support and location pins Active
DIN 6323 Slot stones, loose Active
DIN 6325 Parallel Pins, Hardened; Tolerance Zone m6 Withdrawn DIN EN ISO 8734 ISO 8734
DIN 6340 Washers for clamping devices Active
DIN 6738 Paper and paper board – Lifespan classes Active
DIN 6776 Technical drawings, labeling Withdrawn DIN EN ISO 3098 ISO 3098
DIN 6796 Conical spring washers for bolted connections Active
DIN 6797 Toothed lock washers Withdrawn
DIN 6798 Serrated lock washers Withdrawn
DIN 6799 Lock washers (retaining washers) for shafts Active
DIN 6880 Bright Key Steel; Dimensions, Permissible Variations, Weights Active
DIN 6885-1 Drive Type Fastenings without Taper Action – Part 1: Parallel Keys, Keyways, Deep Pattern Active
DIN 6885-2 Drive Type Fastenings without Taper Action – Part 2: Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and Application Active
DIN 6885-3 Drive Type Fastenings without Taper Action – Part 3: Parallel Keys, Shallow Pattern, Dimensions and Application Active
DIN 6900 Screw and Washer Assemblies Withdrawn DIN EN 10644 EN 10644
DIN 6901 Tapping screw and washer assemblies Withdrawn DIN EN 10510 EN 10510
DIN 6902 Plain washers for screw and washer assemblies Withdrawn DIN EN 10673 EN 10673
DIN 6903 Plain washers for tapping screw and washer assemblies Withdrawn DIN EN 10669 EN 10669
DIN 6912 Hexagon socket head cap screws with center, with low head Active
DIN 6914 High-strength hexagon head bolts with large widths across flats for structural steel bolting Withdrawn DIN EN 14399-4 EN 14399-4
DIN 6915 Steel hexagon nuts with large widths across flats for high-strength structural bolting Withdrawn DIN EN 14399-4 EN 14399-4
DIN 6916 Round washers for high-strength structural steel bolting Withdrawn DIN EN 14399-6 EN 14399-6
DIN 6921 Hexagon flange bolts Withdrawn DIN EN 1665 EN 1665
DIN 6922 Hexagon flange bolts with reduced shank Withdrawn DIN EN 1665 EN 1665
DIN 6923 Hexagon nuts with flange Withdrawn DIN EN 1661 EN 1661
DIN 6924 Prevailing torque type hexagon nuts with nonmetallic insert Withdrawn DIN EN ISO 7040,
DIN EN ISO 10512
ISO 7040,
ISO 10512
DIN 6925 Prevailing torque type all-metal hexagon nuts Withdrawn DIN EN ISO 7042,
DIN EN ISO 10513
ISO 7042,
ISO 10513
DIN 6926 Prevailing torque type hexagon nuts with flange and with non-metallic insert Withdrawn DIN EN 1663, DIN EN 1666 ISO 7043 (modified), ISO 12125 (modified)
DIN 6927 Prevailing torque type all-metal nuts with flange Withdrawn DIN EN 1664, DIN EN 1667 ISO 7044 (modified),
ISO 12126 (modified)
DIN 6935 Cold bending of flat rolled steel Active

DIN 7000 to DIN 7999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 7045 Pan head screws with type H or type Z cross recess – product grade A Active
DIN 7245 Saw blades for web saws Active
DIN 7337 Break mandrel blind rivets Withdrawn DIN EN ISO 14589, DIN EN ISO 15977, DIN EN ISO 15978, DIN EN ISO 15979, DIN EN ISO 15980, DIN EN ISO 15981, DIN EN ISO 15982, DIN EN ISO 15983, DIN EN ISO 15984, DIN EN ISO 16582, DIN EN ISO 16583, DIN EN ISO 16584 ISO 14589, ISO 15977, ISO 15978, ISO 15979, ISO 15980, ISO 15981, ISO 15982, ISO 15983, ISO 15984, ISO 16582, ISO 16583, ISO 16584
DIN 7343 Spiral Pins; Normal Type Withdrawn DIN EN ISO 8750 ISO 8750
DIN 7344 Spiral Pins; Heavy Duty Type Withdrawn DIN EN ISO 8748 ISO 8748
DIN 7346 Spring-Type Straight Pins; (Roll Pins) Light-weight Type Withdrawn DIN EN ISO 13337 ISO 13337
DIN 7349 Plain Washers for Bolts with Heavy Clamping Sleeves Active
DIN 7500-1 Thread rolling screws for metric ISO thread – Part 1: Types, designation, requirements Active
DIN 7500-2 Thread rolling screws for ISO metric thread; guideline values for hole diameters Active
DIN 7504 Self-drilling screws with tapping screw thread – Dimensions, requirements and testing Withdrawn ISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483
DIN 7513 Hexagon head and slotted head thread cutting screws – Dimensions, requirements and testing Active
DIN 7516 Cross recessed head thread cutting screws – Dimensions, requirements and testing Active
DIN 7603 Ring seals and gaskets Active
DIN 7875 Diving accessories for skin divers; terminology Withdrawn
DIN 7876 Diving accessories for skin divers; flippers; dimensions, requirements and testing Withdrawn
DIN 7877 Diving accessories for skin divers; diver's masks; requirements and testing Withdrawn
DIN 7878 Diving accessories for skin divers; snorkel; technical requirements of safety, testing Withdrawn
DIN 7962 Cross recesses for screws; (modified version of ISO 4757) Withdrawn DIN EN ISO 4757 ISO 4757
DIN 7970 Threads and thread ends for tapping screws (modified version of ISO 1478) Withdrawn DIN EN ISO 1478 ISO 1478
DIN 7971 Slotted pan head tapping screws Withdrawn DIN ISO 1481 ISO 1481
DIN 7972 Slotted countersunk head tapping screws Withdrawn DIN ISO 1482 ISO 1482
DIN 7973 Slotted raised countersunk head tapping screws Withdrawn DIN ISO 1483 ISO 1483
DIN 7977 Taper Pins with Thread Ends and Constant Point Lengths Withdrawn DIN EN 28737 ISO 8737
DIN 7978 Taper Pins with Internal Thread Withdrawn DIN EN 28737 ISO 8736
DIN 7979 Parallel Pins with Internal Thread Withdrawn DIN EN ISO 8733,
DIN EN ISO 8735
ISO 8733,
ISO 8735
DIN 7980 Spring lock washers with square ends for cheese head screws Withdrawn
DIN 7981 Cross recessed pan head tapping screws Withdrawn DIN ISO 7049 ISO 7049
DIN 7982 Cross recessed countersunk head tapping screws Withdrawn DIN ISO 7050 ISO 7050
DIN 7983 Countersunk (Flat) Head Tapping Screws with Cross Recess Withdrawn DIN ISO 7051 ISO 7051
DIN 7984 Hexagon socket head cap screws with low head Active
DIN 7985 Cross recessed raised Phillips Pan head screws Withdrawn DIN EN ISO 7045 ISO 7045
DIN 7989-1 Washers for steel structures – Product grade C Active
DIN 7989-2 Washers for steel structures – Product grade A Active
DIN 7991 Hexagon socket countersunk head cap screws Withdrawn DIN EN ISO 10642 ISO 10642

DIN 8000 to DIN 8999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 8074 Polyethylene (PE) pipes – Dimensions Active
DIN 8075 Polyethylene (PE) pipes – PE 63, PE 80, PE 100, PE-HD – General quality requirements, testing Active
DIN 8077/8078 Polypropylene (PP-R) Pipes -PN 20, PN25 PP-R – General quality requirements, testing Active
DIN 8513-1 Brazing and Braze Weld Filler Metals; Copper Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery Withdrawn DIN EN 1044 EN 1044
DIN 8513-2 Brazing and Braze Weld Filler Metals; Silver-bearing Brazing Alloys with less than 20% by wt. Silver; Composition, Use, Technical Conditions of Delivery Withdrawn DIN EN 1044 EN 1044
DIN 8513-3 Brazing filler metals; silver brazing filler metals containing not less than 20% of silver; composition, application, technical delivery conditions Withdrawn DIN EN 1044 EN 1044
DIN 8513-4 Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery Withdrawn DIN EN 1044 EN 1044
DIN 8513-5 Brazing filler metals; Nickel base filler metals for high temperature brazing; Application, composition, technical delivery conditions Withdrawn DIN EN 1044 EN 1044
DIN 8580 Manufacturing processes – Terms and definitions, division Active
DIN 8806-1 Narrow band saw blades for woodworking; dimensions Active
DIN 8515 Defects in Metallic Solder Joints; Brazing Joints and High-temperature Solder Joints; Classification, Designations, Explanatory Notes Withdrawn DIN EN ISO 18279:2004-04

DIN 9000 to DIN 9999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 9021 Plain washers with large outside diameter Withdrawn DIN EN ISO 7093-1, DIN EN ISO 7093-2 ISO 7093-1, ISO 7093-2

DIN 10000 to DIN 19999

[edit]

DIN 10000 to DIN 10999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 10504 Food hygiene – Lamps for the lighting of meat and meat products Withdrawn

DIN 11000 to DIN 11999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 11024 Beta cotter pin (R-pin) – Dimensions, materials Active
DIN 11850 Tubes for the food, chemical and pharmaceutical industry – Stainless steel tubes – Dimensions, materials Withdrawn EN 10357
DIN 11851 Hygienic Unions

DIN 12000 to DIN 12999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 12950-1 Laboratory furniture; safety cabinets for microbiological and biotechnological work; safety requirements, tests Withdrawn
DIN 12950-2 Laboratory furniture; safety cabinets for microbiological and biotechnological work; containment of class 1 and class 2 cabinets, microbiological test Withdrawn
DIN 12950-10 Laboratory furniture; safety cabinets for microbiological and biotechnological work; requirements and testing Withdrawn
DIN 12975-1 Thermal solar systems and components – Solar collectors – Part 1: General requirements
DIN 12975-2 Thermal solar systems and components – Solar collectors – Part 2: Test methods
DIN 12976-1 Thermal solar systems and components – Factory made systems – Part 1: General requirements
DIN 12976-2 Thermal solar systems and components – Factory made systems – Part 2: Test methods

DIN 13000 to DIN 13999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 13080 Division of hospitals into functional areas and functional sections Active
DIN 13260-2 Supply systems for medical gases – Part 2: Dimensions and allocation of probes and gas-specific connection points for terminal units for compressed medical gases and vacuum Active
DIN 13432 Packaging – Requirements for packaging recoverable through composting and biodegradation – Test scheme and evaluation criteria for the final acceptance of packaging Active DIN EN 13432
DIN 13715 Workpiece corners and edges Active DIN ISO 13715(2000–12)

DIN 14000 to DIN 14999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 14090 Areas for the fire brigade on premises Active
DIN 14096-1 Fire precaution regulation – Part 1: General and part A (placard); rules for drafting and placarding Active
DIN 14096-2 Fire precaution regulation – Part 2: Part B (for persons without special tasks of fire prevention and fire fighting); rules for drafting Active
DIN 14096-3 Fire precaution regulation – Part 3: Part C (for persons with special tasks of fire prevention and fire fighting); rules for drafting Active
DIN 14210 Water pool for firefighting Active
DIN 14236 Ultrasonic domestic gas meters Active
DIN 14406-4 Portable fire extinguishers – Part 4: Maintenance Active
DIN 14503 Trailers for firefighting purposes, two-wheeled; general requirements Withdrawn DIN 14521
DIN 14505 Firefighting and rescue service vehicles – Vehicles for roller containers – General requirements Active
DIN 14507 Rescue service vehicles – Vehicles for roller containers – General requirements Active
DIN 14520 Trailers for portable fire pumps Withdrawn
DIN 14521 Firefighting – Trailer with removable foam-water monitor Active
DIN 14530-5 Fire fighting vehicles – Part 5: Group pumping appliance LF 10/6, Group pumping appliance for rescue operations HLF 10/6 Active
DIN 14530-11 Fire fighting vehicles – Part 11: Group pumping appliance LF 20/16, Group pumping appliance for rescue operations HLF 20/16 Active
DIN 14530-16 Fire fighting vehicles – Part 16: Pumping appliance TSF Active
DIN 14530-17 Fire fighting vehicles – Part 17: Pumping appliance TSF-W Active
DIN 14530-21 Fire fighting vehicles – Part 21: Pump water tanker TLF 20/40, Pump water tanker TLF 20/40-SL Active
DIN 14530-22 Fire fighting vehicles – Part 22: TLF 16/24-TR Active
DIN 14530-24 Fire fighting vehicles – Part 24: Small pumping appliance KLF Active
DIN 14530-25 Fire fighting vehicles – Part 25: Pumping appliance STLF 10/6 Active
DIN 14555-1 Vehicles carrying tools and gears – Part 1: General requirements Active
DIN 14555-3 Vehicles carrying tools and gears – Part 3: Emergency tender RW Active
DIN 14555-12 Vehicles carrying tools and gears – Part 12: Damage control tender GW-G Active
DIN 14555-21 Vehicles carrying tools and gears – Part 21: GW-L1 for logistic tasks Active
DIN 14555-22 Vehicles carrying tools and gears – Part 22: GW-L2 for logistic tasks Active
DIN 14565 Fire hose tender; Type SW 2000-TR Withdrawn
DIN 14701-1 Turntable ladders and similar fire fighting vehicles; Purpose, concepts, safety equipment, requirements Withdrawn DIN EN 1777 EN 1777
DIN 14701-2 Turntable ladders and similar fire fighting vehicles; Turn table ladders, engine driven Withdrawn DIN EN 14043, DIN EN 14044 EN 14043, EN 14044
DIN 14701-3 Turntable ladders and similar fire fighting vehicles; Rescue baskets Withdrawn DIN EN 1777 EN 1777
DIN 14702 Turntable ladder DL 16–4, hand operating Active
DIN 14703 Trailer Ladder AL 16-4 Active
DIN 14710-1 Hook ladder, manufactured using wood; with hinged hook Withdrawn DIN EN 1147 EN 1147
DIN 14710-3 Hook light metal ladder Withdrawn
DIN 14711-1 Scaling ladder; made from wood Withdrawn DIN EN 1147 EN 1147
DIN 14711-2 Scaling ladder; made from light metal Withdrawn DIN EN 1147 EN 1147
DIN 14711-3 Scaling ladder; socket rungs and socket parts Withdrawn DIN EN 1147 EN 1147
DIN 14713 Folding ladder Withdrawn DIN EN 1147 EN 1147
DIN 14715-1 Three piece extension ladder made from wood Withdrawn DIN EN 1147 EN 1147
DIN 14715-2 Three piece extension ladder; made of light metal Withdrawn DIN EN 1147 EN 1147

DIN 15000 to DIN 15999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 15018-2 Cranes; steel structures; principles of design and construction Active
DIN 15185-1 Warehouse systems with guided industrial trucks; requirements on the ground, the warehouse and other requirements Active
DIN 15185-2 Warehousesystems with powered industrials trucks; code of practice for the protection of persons when operating with trucks in narrow aisles; safety requirements, testing Active
DIN 15721 Film 70 mm; projection reel Active

DIN 16000 to DIN 16999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 16518 Classification of types Active
DIN 16892 Cross-linked high-density polyethylene (PE-X) pipes – General quality requirements and testing Active
DIN 16893 Cross-linked high-density polyethylene (PE-X) pipes – Dimensions Active

DIN 17000 to DIN 17999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 17175 Seamless Tubes of heat Resistant Steels Withdrawn DIN EN 10216-2
DIN 17200 Steels For Quenching And Tempering – Technical Delivery Conditions Superseded DIN 10083-1
DIN 10083-2
DIN 10083-3
DIN 17240 Heat Resisting and Highly Heat Resisting Materials for Bolts and Nuts; Quality Specifications Withdrawn DIN EN 10269
DIN 17410 Materials for permanent magnets: Technical conditions Active
DIN 17457 Withdrawn DIN EN 10217-7
DIN 17458 Withdrawn DIN EN 10216-5
DIN 17471 Resistance alloys Active

DIN 18000 to DIN 18999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 18012 House service connections facilities – Principles for planning Active
DIN 18013 Recesses for meter boards (electric meters) Active
DIN 18014 Foundation earth electrode – General planning criteria Active
DIN 18015-1 Electrical installations in residential buildings – Part 1: Planning principles Active
DIN 18015-2 Electrical installations in residential buildings – Part 2: Nature and extent of minimum equipment Active
DIN 18015-3 Electrical installations in residential buildings – Part 3: Wiring and disposition of electrical equipment Active
DIN 18022 Domestic kitchens, bathrooms and WCs; design principles Withdrawn
DIN 18024-1 Barrier-free built environment – Part 1: Streets, squares, paths, public transport, recreation areas and playgrounds – Design principles Active
DIN 18024-2 Construction of accessible buildings – Part 2: Publicly accessible buildings and workplaces, design principles Active
DIN 18065 Stairs in buildings – Terminology, measuring rules, main dimensions Active
DIN 18379 Construction contract procedures (VOB) – Part C: General technical specifications in construction contracts (ATV) – Installation of air conditioning systems Active
DIN 18382 Contract procedures for building works – Part C: General technical specifications for building works; Low-voltage installation and medium-voltage installation with nominal voltages up to including 36 kV Active
DIN 18384 Construction contract procedures (VOB) – Part C: General technical specifications in construction contracts (ATV); Installation of lightning protection systems Active
DIN 18800-1 Steel structures – Part 1: Design and construction Withdrawn DIN EN 1993
DIN EN 1090
DIN 18800-2 Steel structures – Part 2: Analysis of safety against buckling of linear members and frames Withdrawn DIN EN 1993
DIN 18800-3 Steel structures – Part 3: Analysis of safety against buckling of plates Withdrawn DIN EN 1993
DIN 18800-4 Steel structures – Part 4: Analysis of safety against buckling of shells Withdrawn DIN EN 1993
DIN 18800-5 Steel structures – Part 5: Composite structures of steel and concrete – Design and construction Withdrawn DIN EN 1994
DIN 18800-7 Steel structures – Part 7: Execution and constructor's qualification Active EN 1090-2

DIN 19000 to DIN 19999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN V 19222 Control technology – Terminology Active
DIN 19225 Measurement and control; terminology and classification of controllers Active
DIN 19226-1 Control technology – Part 1: General terms and definitions Active
DIN 19226-2 Control technology – Part 2: Terms and definitions; dynamic systems behaviour Active
DIN 19226-3 Control technology – Part 3: Terms and definitions of switching systems behaviour Active
DIN 19226-4 Control technology – Part 4: Terms and definitions of control systems Active
DIN 19226-5 Control technology – Part 5: Functional terms Active
DIN 19226-6 Control technology – Part 6: Terms and definitions of functional and constructional units Active
DIN 19227-1 Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions Active
DIN 19227-2 Control technology; graphical symbols and identifying letters for process control engineering; representation of details Active
DIN 19237 Measurement and control; control engineering vocabulary Withdrawn DIN 19226-3, DIN 19226-4,
DIN 19226-5, DIN 19226-6
DIN 19227-1 Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions Withdrawn DIN EN 62424
DIN 19227-2 Control technology; graphical symbols and identifying letters for process control engineering; representation of details Active
DIN 19533 Pipe-lines of high-density PE (high-density polyethylene) and low-density PE (low-density polyethylene) for drinking water supply; pipes, pipe connections and fittings for pipe-lines Withdrawn DIN EN 12201-1,
DIN EN 12201-2,
DIN EN 12201-3,
DIN EN 12201-5
EN 12201-1,
EN 12201-2,
EN 12201-3,
EN 12201-5
DIN 19704-1 Hydraulic steel structures – Part 1: Criteria for design and calculation Active
DIN 19704-2 Hydraulic steel structures – Part 2: Design and manufacturing Active
DIN 19704-3 Hydraulic steel structures – Part 3: Electrical equipment Active

DIN 20000 to DIN 29999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 20066 Fluid technology – hose lines, dimensions, specifications
DIN 20163 Explosives work
DIN 21800 Hammer and pick signs (mining symbol)
DIN 21908 Mining crevice work; colours
DIN 22101 Conveyor belt for bulk material, fundamentals, analysis and design
DIN 22107 Arrangements for belt conveyor rollers
DIN 22112 Rollers: dimensions, specifications, testing
DIN 23307 Seat leathers for the mining industry (miner's apron)
DIN 23342 Clothing for the mining industry – men's vest with 1/4 sleeves
DIN 23345 Clothing for the mining industry – men's underpants 1/1 length (Long Johns)

DIN 24000 to DIN 24999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 24190 Ventilation and air conditioning – folded and welded rectangular sheet metal ducts Withdrawn
DIN 24271-1 Centralised lubrication systems – Concepts – Part 1: Classification Active
DIN 24340-2 Hydraulic valves; mounting surfaces and connecting plates for directional control valves Active
DIN 24537 Welding, Warping valves; Steel Grating Floor Standard control valves Active

DIN 28000 to DIN 28999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 28610-1 Ductile iron pressure pipes with socket with cement-mortar lining for gas and water pipelines; dimensions and masses Withdrawn DIN EN 545, DIN EN 969 EN 545, EN 969
DIN 28610-2 Ductile iron pressure pipes with socket for gas and water pipelines rated for pressures over 4 bar up to and including 16 bar; dimensions and masses Withdrawn DIN EN 969 EN 969

DIN 30000 to DIN 39999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 30722-1 Roller contact tipper vehicles, roller containers – Part 1: Roller contact tipper vehicles up to 26 t, roller containers type 1570 made from steel Active
DIN 30722-2 Roller contact tipper vehicles, roller containers – Part 2: Roller contact tipper vehicles up to 32 t, roller containers type 1570 made from steel Active
DIN 30722-3 Roller contact tipper vehicles, roller containers – Part 3: Roller contact tipper vehicles up to 12 t, roller containers type 900 made from steel Active
DIN 30722-4 Roller containers for the transport on road and rail Active

DIN 31000 to DIN 31999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 31635 Conversion of the Arabic alphabet Active
DIN 32676 Tri-Clamp Fittings[2] Active

DIN 40000 to DIN 49999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 40015 Frequency and wave bands Active
DIN 40020 Guidelines for the user interface in multimedia equipment for general purpose use (IEC/TR 61997:2001) Active
DIN 40050-9 Road vehicles; degrees of protection (IP-code); protection against foreign objects; water and contact; electrical equipment Active
DIN 40101-1 Graphical symbols for use on equipment Withdrawn
DIN 40101-2 Graphical symbols for use on equipment; graphical symbols from ISO 7000 for electrical engineering Active
DIN 40108 Electric power technology – Current systems – Concepts, quantities, letter symbols Active
DIN 40110-1 Quantities used in alternating current theory – Part 2: Two-line circuits Active
DIN 40110-2 Quantities used in alternating current theory – Part 2: Multi-line circuits Active
DIN 40146-1 Telecommunications – Part 1: Basic concepts Active
DIN 40148-1 Transmission systems and two-ports; concepts and quantities Active
DIN 40148-2 Transmission systems and two-ports; symmetry characteristics of linear two-ports Active
DIN 40148-3 Transmission systems and two-ports; measures for attenuation Active
DIN 40200 Nominal value, limiting value, rated value, rating – concepts Active
DIN 41215 Electrical communication engineering; electromagnetic relays, definitions Withdrawn
DIN 41301 Electro Sheets; Magnetic Materials for Transformers Withdrawn
DIN 41309-1 Small transformers and chokes; strip-wound cut cores; types SM, SE, SU, SG and S3U; dimensions materials Withdrawn
DIN 41309-2 Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for one phase applications; types SM, SE, SU and SG Withdrawn
DIN 41309-3 Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for three phase applications; type S3U Withdrawn
DIN 41426 Nominal values of resistors and capacitors Withdrawn DIN IEC 60063 IEC 60063
DIN 41429 Colour code for fixed resistors Withdrawn DIN EN 60062 EN 60062
DIN 41524 Circular connectors for radio and associated sound equipment three and five-pole connectors Withdrawn
DIN 41612-1 Two-part connectors for printed board, grid 2,54 mm; common mounting features; survey of types Withdrawn DIN 41612-1 S1
DIN 41612-1 S1 Two piece connectors for printed circuits, grid 2,54 mm (0,1 in); general allusions Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-2 Two-part connectors for printed boards; grid 2,54mm; dimensions of types B, C and D Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-3 Two part connectors for printed boards; grid 2,54mm; dimensions of types F and G Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-4 Two-part connectors for printed boards; grid 2,54mm, dimensions of type H Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-5 Two-part connectors for printed boards; grid 2,54mm; ratings, requirements, tests Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-6 Two-part connection for printed boards; grid 2.54mm; dimensions of types Q, R and S Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-7 Two-part connectors for printed boards; grid 2,54 mm; dimensions of types U and V Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-8 Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-8 S1 Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M; survey of special contracts for use with type M Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-9 Two-part connectors for printed boards; grid 2,54 mm; dimensions of type E Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-10 Two-part connectors for printed boards; grid 2,54mm; gauges Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-102 Two-part connectors for printed boards; dimensions for type X Withdrawn DIN 41612-9
DIN 41612-103 Two-part connectors for printed boards; dimensions of type M Withdrawn DIN 41612-8
DIN 41652-1 Rack and panel connectors, trapezoidal, round contacts 1 mm; common mounting features and dimensions; survey of types Active
DIN 41652-2 Rack and panel connectors; trapezoidal, round contacts 1 mm; ratings, requirements, tests Active
DIN 41750-1 Rack and panel connectors, trapezoidal, round contacts ø1 mm; common mounting features and dimensions; survey of types Active
DIN 41750-2 Rack and panel connectors, trapezoidal, round contacts ø1 mm; ratings, requirements, tests Active
DIN 41750-3 Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type A; solder termination for free wiring Active
DIN 41750-5 Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type C; crimp termination for free wiring Active
DIN 41782 Guidelines for the presentation of published data Withdrawn DIN IEC 60747-2 IEC 60747-2
DIN 41786 Thyristors, definitions Withdrawn
DIN 41855 Semiconductor devices and integrated circuits; kinds of devices and general terms Withdrawn
DIN 41855-2 Semiconductor devices and integrated circuits; optoelectronic semiconductor devices; terms and definitions Withdrawn
DIN 41868 Cases 10 A 3 and 10 B 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-1 Case 23 A 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-2 Cases 34 A 2 and 34 A 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-3 Case 11 A 3 and 11 B 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-4 Case 12 A 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-5 Case 13 A 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-6 Case 14 A 3 for semiconductor devices; main dimensions Withdrawn
DIN 41869-7 Case type 15 for semiconductor devices; main dimensions Withdrawn
DIN 41873 Cases type 5 for semiconductor devices and integrated circuits Withdrawn
DIN 41876 Cases 18 A, B and C with 2 up to 4 terminals for semiconductor devices; main dimensions Withdrawn
DIN 42400 Terminal markings for electrical equipment; general rules, alphanumeric system Withdrawn DIN EN 60445 EN 60445
DIN 42402 Terminal markings for power transformers and reactors Active
DIN 42403 Terminal markings for power converters Withdrawn DIN IEC 61148 IEC 61148
DIN 42673-1 Totally enclosed fan-cooled three-phase induction motors squirrel-cage, type IM B 3, with rolling bearing; mounting dimensions and relationship frame sizes-output ratings Withdrawn
DIN 42673-2 Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes – output ratings for type of protection increased safety "e" Active
DIN 42673-3 Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes – output ratings for type of protection flameproof enclosure "d" Active
DIN 42673-4 Totally enclosed fan-cooled alternating-current polyphase motors with squirrel-cage, design B3, with ball bearings, maximum envelope dimensions Active
DIN 42802 Touch-protected connector for electromedicine Active
DIN 42961 Rating plates for rotating electrical machinery; design Active
DIN 42973 Rated output values for rotating electrical machinery for continuous duty Active
DIN 43700 Measurement and control – Measurement and control instruments for panel mounting – Nominal front- and cut-out-dimensions Withdrawn DIN IEC 61554 IEC 61554
DIN 43780 Electrical measuring instruments; direct acting indicating electrical measuring instruments and their accessories Withdrawn DIN EN 60051-1 EN 60051-1
DIN 43802-2 Line scales and pointers for indicating electrical measuring instruments; general requirements Active
DIN 43802-3 Line scales and pointers for indicating electrical measuring instruments; designs and dimensions Active
DIN 43802-4 Line scales and pointers for indicating electrical measuring instruments; scale graduation and numbering Active
DIN 43807 Measuring and control; electrical measuring instruments; terminal markings for switchboard meters, panel meters and measuring transducers for the measurement of power and power factor Active
DIN 43856 Electricity meters, tariff time switches and ripple control receivers; connection diagrams, terminal marking, circuit diagrams Active
DIN 43856-2 Electricity meters – Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995 Active
DIN 43870-1 Meter mounting boards; dimensions based on a grid system Active
DIN 43870-2 Meter mounting boards; functional area Active
DIN 43870-3 Meter panels; wirings Active
DIN 43880 Modular electronics housings Active
DIN 44070-1 Meter mounting boards; dimensions based on a grid system Active
DIN 44070-2 Meter mounting boards; functional area Active
DIN 44070-3 Meter panels; wirings Active
DIN 44070-4 Meter panels; cover for wiring Active
DIN 44080 Thermistors; PTC, technical terms and tests Withdrawn
DIN 44300 Information processing; vocabulary Withdrawn
DIN 44300-1 Information processing – Concepts – General terms Withdrawn
DIN 44300-2 Information processing – Concepts – Representation of data Withdrawn
DIN 44300-3 Information processing – Concepts – Data structures Withdrawn
DIN 44300-4 Information processing – Concepts – Programming Withdrawn
DIN 44300-5 Information processing – Concepts – Components of digital computer systems Withdrawn
DIN 44300-6 Information processing – Concepts – Storage Withdrawn
DIN 44300-7 Information processing – Concepts – Times Withdrawn
DIN 44300-8 Information processing – Concepts – Processing functions Withdrawn
DIN 44300-9 Information processing – Concepts – Process relations and modes of operation Withdrawn
DIN 45322 Circular connectors for radio and associated sound equipment; six-pole connectors Withdrawn DIN EN 60130-9 EN 60130-9
DIN 45323 Connectors for coupling an external low-voltage power to portable entertainment equipment (describes at least two DC coaxial power plugs) Active
DIN 45500-1 High fidelity audio equipment and systems; minimum performance requirements; Part 1: general Withdrawn DIN EN 61305-1 EN 61305-1
DIN 45500-2 High fidelity audio equipment and systems; requirements for tuner equipments Withdrawn DIN EN 61305-2 EN 61305-2
DIN 45500-3 High fidelity audio equipment and systems; requirements for disk record reproducing equipments Withdrawn
DIN 45500-4 High fidelity audio equipment and systems; minimum performance requirements for magnetic recording and reproducing equipment Withdrawn
DIN 45500-5 High fidelity audio equipment and systems; minimum performance requirements for microphones Withdrawn
DIN 45500-6 High fidelity audio equipment and systems; minimum performance requirements for amplifiers Withdrawn DIN EN 61305-3 EN 61305-3
DIN 45500-7 High fidelity audio equipment and systems; requirements for loudspeakers Withdrawn DIN EN 61305-5 EN 61305-5
DIN 45500-8 High fidelity audio equipment and systems; for sets and systems Withdrawn
DIN 45500-9 High fidelity audio equipment and systems; minimum requirements for magnetic tapes 4 and 6 for audio recordings Withdrawn
DIN 45500-10 High fidelity audio equipment and systems; minimum performance requirements for headphones Withdrawn
DIN 45507 Measuring apparatus for frequency variations in sound recording equipment Withdrawn DIN IEC 60386 IEC 60386
DIN 45539 Disk record reproducing equipment; directives for measurements, markings and audio frequency connections, dimensions of interchangeable pickups, requirements of play back amplifiers Withdrawn DIN IEC 60098 IEC 60098
DIN 45596 Microphones; phantom powering Withdrawn
DIN 46400-1 Steel flats with special magnetic properties cold rolled, non – oriented, finally annealed magnetic sheet and strip hysteresis loss at frequencies above 100 Hz Withdrawn DIN EN 10106 EN 10106
DIN 46400-3 Grain-oriented magnetic steel and strip technical conditions Withdrawn DIN EN 10107 EN 10107
DIN 47100 Cords for telecommunication; code of insulated conductors, colour of sheath Withdrawn
DIN 47301-1 Terms of HF-lines Active
DIN 47301-2 Terms of HF-lines Active
DIN 47301-3 Definition of radio frequency transmission lines – mean characteristic impedance – mean standing wave ratio Active
DIN 48803 Lightning protection system; Arrangement of components and dimensions for mounting Withdrawn
DIN 48830 Lightning protection system; Description Withdrawn

DIN 51097 to DIN 59999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 51097 Testing of floor coverings; determination of the anti-slip properties: wet-loaded barefoot areas; walking method; ramp test Withdrawn DIN 51130
DIN 51130 Testing of floor coverings; determination of the anti-slip properties: workrooms and fields of activities with slip danger, walking method – ramp test Withdrawn DIN 51097
DIN 51501 Lubricants; Lubricating Oils L-AN; Minimum Requirements Withdrawn
DIN 52368 Testing of particleboards; determination of formaldehyde emission by gas analysis Withdrawn DIN EN 717-2 EN 717-2
DIN 53150 Paints and varnishes – Determination of the drying stage of coatings (modified Bandow-Wolff method) Active
DIN 53438 Testing of combustible materials; response to ignition by small flame Active
DIN 53452 Testing of Plastics; Flexural Test Withdrawn DIN EN ISO 178 ISO 178
DIN 53575 Flexible Cellular Polymeric Materials – Determination of Tear Strength Withdrawn DIN EN ISO 8067 ISO 8067
DIN 54836 Testing of combustible materials; determination of ignition temperature Active
DIN 54837 Determination of burning behaviour using a gas burner Active
DIN 55003-3 Machine tools; symbols; numerically controlled machine tools Withdrawn
DIN 58145 Measuring Method for determination of solarization effect of fused silica optical fibers Active
DIN 58810 Surgical implants; threads for bone screws and nuts Withdrawn
DIN 58888 Thread connection for microscope objectives Withdrawn DIN ISO 8038-1 ISO 8038-1

DIN ISO 53438

DIN 60000 to DIN 69999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 66000 Information processing; switching algebra, mathematical signs and symbols Active
DIN 66001 Information processing; graphical symbols and their application Active
DIN 66002 Information processing; handwriting of the digit 0 and of the upper case letter O Active
DIN 66003 Information technology – 7-bit code Active
DIN 66004-1 Information processing – Coding on data media – Part 1: Representation of 7-bit code character sets on punched tape 25 Active
DIN 66004-2 Information processing – Coding on data media – Part 2: Representation of 7-bit coded and 8-bit coded character sets on punched cards Active
DIN 66004-3 Information processing – Coding on data media – Part 3: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12 Active
DIN 66004-4 Information processing – Coding on data media – Part 4: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8 Active
DIN 66004-5 Information processing – Coding on data media – Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridge Active
DIN 66005 Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12 Active
DIN 66006 Presentation of ALGOL/ALCOR programs on paper tape and punch cards Withdrawn
DIN 66007 Font CMC 7 for magnetic ink character recognition; characters and nominal dimensions Withdrawn DIN ISO 1004 ISO 1004
DIN 66008-1 Font A for optical character recognition; characters and nominal dimensions Active
DIN 66008-6 Font A for optical character recognition; characters and nominal dimensions; extension of the character set Active
DIN 66008-7 Font A for optical character recognition; representation of characters by dots in a 9 × 9 matrix Active
DIN 66009 Font B for optical character recognition; character Withdrawn
DIN 66020-1 Functional requirements for the interface between data terminal equipment and data circuit-terminating equipment – Part 1: General application Active
DIN 66020-2 List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) in public data networks Active
DIN 66020-4 Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE) Active
DIN 66020-9 Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per second Active
DIN 66021-1 Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE) Active
DIN 66021-2 Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per second Active
DIN 66025-1 Numerical control of machines, format; general requirements Active
DIN 66025-2 Industrial automation; numerical control of machines; format, preparatory and miscellaneous functions Active
DIN 66027 Information processing; programming language FORTRAN Withdrawn
DIN 66215-1 Programming of numerically controlled machines; CLDATA, general structure and record types Active
DIN 66215-2 Programming of numerically controlled machines; CLDATA; minor elements of type 2000 records (post-processor commands) Active
DIN 66253-2 Information processing; programming language PEARL 1998
DIN 66234 Information processing; programming language PL/I Active
DIN 66255 Information processing; programming language PL/I Active
DIN 66256 Information processing; programming language Pascal Withdrawn
DIN 66257 Numerical control of machines; concepts Withdrawn DIN ISO 2806 ISO 2806
DIN 66258-1 Interfaces and basic data link control procedures for data communication; C S-interface, V S-interface Withdrawn
DIN 66258-2 Interface and basic data link control procedures for data communication; balanced interface for start-stop transmission using basic data link control procedures on point-to-point connection Withdrawn
DIN 66261 Information processing; Nassi-Shneiderman flowchart symbols Active
DIN 66264-1 Industrial automation systems and integration – Multiprocessor Control System for Industrial Machines (MPST) – Part 1: Parallel bus Active
DIN 66264-2 Multiprocessor control system for industrial machines (MPST); industrial automatics; rules for information interchange Active
DIN 66303 Information technology – 8 bit code Active
DIN V 66304 Industrial automation; Computer Aided Design; format for the exchange of standard parts data Active
DIN 66325-2 Local and Metropolitan Area Networks; LLC; identical with ISO 8802-2:1989 Withdrawn ISO 8802-2
DIN 66325-4 Local and Metropolitan Area Networks; token-passing bus access method; identical with ISO/IEC 8802-4:1990 Withdrawn ISO/IEC 8802-4
DIN 66399 Three-part standard regarding the seven security levels of paper shredders; replaces DIN 32757 Active
DIN 69901 Project controlling; project management; concepts Active

DIN 70000 to DIN 79999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 71412 Lubricating nipples; cone type Active
DIN 72311-1 Lead storage batteries; starter batteries for motorcycles, nominal capacities, main dimensions Active
DIN 72311-4 Lead storage batteries; starter batteries, terminals, vent plugs and filler openings Active
DIN 72311-8 Lead storage batteries; starter batteries for motor cycles and passenger cars Active
DIN 72311-13 Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45 and 54 Ah, for lateral basic fastening 10,5 Active
DIN 72311-16 Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45, 54 and 63 Ah, for lateral basic fastening 19 Active
DIN 72311-17 Lead storage batteries; starter batteries, protective covering for terminal Active
DIN 72311-18 Lead storage batteries; starter batteries with basic fastening 10,5 for passenger cars and commercial vehicles; nominal capacities, main dimensions Active
DIN 72311-20 Lead storage batteries; starter batteries for commercial vehicles; nominal capacities and main dimensions Active
DIN 72311-21 Lead storage batteries; starter batteries with 10,5 basic fastening lugs for commercial vehicles; nominal capacities and main dimensions Active
DIN 72552-1 Terminal markings for motor vehicles; scope, principles, requirements Active
DIN 72552-2 Terminal markings for motor vehicles; codes Active
DIN 72552-3 Terminal markings for motor vehicles; examples for application on circuit diagrams Active
DIN 72552-4 Terminal markings for motor vehicles; summary Active
DIN 75490 Radio communication devices in motor vehicles; installation space, general requirements Active

DIN 80000 to DIN 99999

[edit]
DIN Title Status DIN replacement Other org
replacement
DIN 91379 Characters and defined character sequences in Unicode for the electronic processing of names and data exchange in Europe Active

See also

[edit]

References

[edit]
  1. ^ DK 621.882.245 Deutsche Normen Dec. 1952 Linsensenkschrauben mit Längsschlitz
  2. ^ "What is DIN 32676? | Sanitary Fittings". sanitaryfittings.us. 28 June 2017. Retrieved 18 September 2018.
[edit]